 |
 |
Home Canning Questions And Answers |
General QuestionsQ. What causes jars to break? A. There are several types of breaks that occur. Each break looks different and has specific causes. |
|
|
|
Home Canning Questions And Answers |
General QuestionsQ. What causes jars to break? A. There are several types of breaks that occur. Each break looks different and has specific causes. |
Thermal shock is characterized by a crack running around the base of the lower part of the jar, sometimes extending up the side. To prevent thermal breakage:
Internal pressure break is characterized by the origin of the break on the side. It is in the form of a vertical crack that divides and forks into two fissures. To prevent pressure breaks:
Impact breaks originate at the point of impact and fissures radiate from the point of contact. To prevent impact breaks:
Q. How can I determine if a jar of canned food is sealed?
A. Cool jars for 12 to 24 hours, remove the screwbands, and test seals with one of the following options:
Q. When should lids with screwbands be tightened on the jars?
A. Before placing filled jars in the boiling waterbath canner or pressure-canner, tightly screw down screwbands and leave in this tightened position. Do not tighten screwbands after processing. Tightening after processing can result in breaking the seal.
Q. How tightly should screwbands be put on when closing jars with two-piece lids?
A. Put on screwbands firmly so that they are handtight. If they are applied too tightly, the flat may buckle.
Q. What causes lids to buckle?
A. The buildup of pressure inside jars causes lids to buckle. This is a result of putting screwbands on so tightly that air can hardly escape from the jars during processing. Buckling may cause tiny pinholes in the flat. For this reason, the food should not be stored on the shelf. Within 24 hours of processing, foods can be refrigerated and used within 1 to 2 days, or reprocessed.
Q. What causes lids not to seal?
A. Failure of lids to seal may be caused by one or more of the following:
Q. Can lids and screwbands be reused?
A. Do not reuse flat metal lids with sealing compound. Screwbands in good condition may be reused.
Q. Can food be reprocessed if it was incorrectly processed or if lids failed to seal?
A. If no more than 24 hours have gone by since the food was processed, do one of the following:
If more than 24 hours have passed since the food was processed, discard it.
Q. When should jars be sterilized?
A. All jams, jellies, and pickled products processed less than 10 minutes should be filled into sterile, empty jars. To sterilize empty jars, put them right side up on a rack in a boiling-water canner. Fill the canner and jars with hot (not boiling) water to 1 inch above the tops of the jars. Boil 10 minutes. Remove and drain hot sterilized jars one at a time. Save the hot water for processing filled jars.
Empty jars used for vegetables, meats, and fruits to be processed in a pressure canner need not be pre-sterilized. It is also not necessary to pre-sterilize jars for fruits, tomatoes, and pickled or fermented products that will be processed 10 minutes or longer in a boiling-water canner.
Q. What is the best way to clean jars before canning?
A. Before every use, wash empty jars in hot water with detergent and rinse well by hand, or wash in a dishwasher. Detergent residue may cause unnatural flavors and colors. These washing methods do not sterilize jars. Scale or hard-water films on jars are easily removed by soaking jars several hours in a solution containing 1 cup of vinegar (5 percent acidity) per gallon of water.
Q. Is it all right to let jars cool in the water in which they were processed?
A. It is important to remove jars from a boiling-water canner immediately when the processing time is up. The spores of certain thermophilic, or heat-loving bacteria, can survive boiling-water processing. Because these bacteria thrive at high temperatures, they can multiply and cause spoilage if canning jars are left in the hot water to cool slowly. When processing foods in a steam-pressure canner, the canner is removed from the heat source when the processing time is up. Jars are left in the steam-pressure canner until the pressure returns to zero naturally. This period of time, after removal from heat until the pressure reaches zero, is considered part of the processing time and is necessary for destruction of microorganisms. Do not rush this cooling by placing the canner under water, or by using a fan. Remove the jars immediately when the pressure returns to zero, and cool at room temperature.
Q. Why do the undersides of metal lids sometimes discolor?
A. Natural compounds in some foods corrode the metal and make a brown or black deposit on the underside of the lid. This deposit is harmless.
Q. What makes canned foods change color?
A. Oxidation may cause foods to darken at the tops of jars. Oxidation is from air in the jars or too little heating or processing to destroy enzymes. Overprocessing may cause discolored foods throughout the containers. Pink and blue colors sometimes seen in canned pears, apples, and peaches are caused by chemical changes in the coloring matter of the fruit. Iron and copper from cooking utensils (or from water in some localities) may cause brown, black, and gray colors in some foods. When canned corn turns brown, the discoloring may be due to the variety of the corn, to stage of ripeness, to overprocessing, or to copper or iron pans. Packing liquid may dissolve coloring materials from the foods.
Q. Is it safe to eat discolored canned foods?
A. The color changes noted do not mean the food is unsafe to eat. Spoilage, however, may also cause color changes. Before you use any canned food that has an unusual color, examine carefully.
Q. Why is open-kettle canning no longer recommended?
A. Temperatures in open-kettle canning are not high enough to destroy spoilage organisms that may be in food. Spoilage bacteria may also enter the food when it is transferred from kettle to jar. Open-kettle canning is not recommended.
Q. Why is headspace important in canning?
A. Headspace is the distance between the surface of food and the underside of the lid. This space allows for the expansion of food solids or bubbling up of liquid during processing. If headspace is not adequate, some food in the container will be forced out, leaving food particles or syrup on the sealing surface and preventing a seal. When too much headspace is allowed, some air may remain in the jar after processing, causing food at the top of the jar to darken. Adequate headspace allows a vacuum to form during the processing of the food.
Q. Why is liquid sometimes lost from glass jars during processing?
A. The most common reasons for loss of liquid are packing jars too full, packing food too tightly into jars, fluctuating pressure in a pressure canner, or lowering pressure too suddenly. If all air bubbles are not removed from jars before processing, the liquid may be lower in jars after processing.
Q. Should liquid lost during processing be replaced?
A. No, never open a jar and refill with liquid (this would let in bacteria and you would need to process again). Loss of liquid does not cause food to spoil, though food above the liquid may darken.
Q. Is it safe to use home-canned food if liquid is cloudy?
A. Cloudy liquid may be a sign of spoilage, but it may be caused by the minerals in hard water or by starch from overripe vegetables. If liquid is cloudy, boil the food. Do not taste or use any food that foams during heating or has an off-odor.
Q. How often should a pressure-canner gauge be checked?
A. Check dial gauges each year. Check them more often if the lid is dropped or submerged in water, the gauge glass is broken, or any parts are rusty. A weighted gauge does not get out of adjustment and does not need to be checked for accuracy. It does need to be cleaned.
Q. Can a pressure saucepan be used for home canning low-acid foods?
A. Pressure saucepans are not recommended for canning.
Q. Can a microwave oven be used for home canning?
A. A microwave oven cannot be used for home canning. Low-acid foods must be processed at 240 degrees Fahrenheit; a microwave can only reach 212 degrees Fahrenheit. Even acid foods must have the uniform heat provided by a conventional water-bath canner. Because of its uneven heating pattern, a microwave does not assure consistent heat to each jar during processing. There also is a danger of explosion of jars during heating or as the jars are removed from the oven.
Q. Can a conventional oven be used to process foods?
A. Oven canning is extremely dangerous and definitely not a recommended procedure. The risk of jars breaking during heating, when the oven door is opened, or when jars are removed from the oven is extremely great. The danger of inadequate processing can also pose a health risk. Heat transfer in the oven is uneven and the food does not reach high enough temperatures. Oven canning is dangerous and not recommended.
Q. Is a steam canner safe for canning foods at home?
A. A steam canner is not the same as a pressure canner. Steam canners are not recommended for home canning because processing times for use with current models have not been adequately researched. Because steam canners do not heat foods in the same manner as do boiling-water canners or pressure canners, their use with boiling-water process times may result in spoilage.
Q. How can spoiled, home-canned food be safely disposed of and the jars cleaned?
A. Spoiled low-acid foods, including tomatoes, may exhibit different kinds of spoilage evidence or very little evidence. Therefore, all suspect containers of spoiled low-acid foods, including tomatoes, should be treated as having produced botulinum toxin and handled carefully in one of two ways:
Detoxification process: Carefully place the suspect containers and lids on their sides in an 8-quart or larger stock pot, pan, or boiling-water canner. Wash your hands thoroughly. Carefully add water to the pot. The water should completely cover the container with a minimum of a 1-inch level above the containers. Avoid splashing the water. Place a lid on the pot and heat the water to boiling. Boil 30 minutes to ensure detoxifying the food and all container components. Cool and discard the containers, their lids, and food in the trash or bury in the soil. Thoroughly scrub all counters, containers, and equipment, including can opener, clothing, and hands that may have been in contact with the food or containers. Discard any sponges or washcloths that may have been used in the cleanup. Place them in a plastic bag and discard in the trash.
Q. Why should a steam-pressure canner be used for canning vegetables?
A. Higher temperatures are required to destroy botulinum bacteria in low-acid food such as meats, fish, poultry, and all vegetables except tomatoes. The only safe way to can these foods is by using a pressure canner, which provides temperatures (240 degrees Fahrenheit) higher than those of boiling water (212 degrees Fahrenheit).
Q. Is it safe to can without salt and sugar?
A. Salt and sugar are not necessary for safe processing of fruits and vegetables. The salt in recipes for pickled products and sugar in jams, preserves, and jellies should not be reduced since the measures given are needed to provide good quality.
Q. Why does canned fruit sometimes float in jars?
A. Fruit may float because pack is too loose or syrup too heavy, or because some air remains in tissues of the fruit after heating and processing.
Q. Is it a good practice to puree and home can foods for infants?
A. If you have time and the food, this may be a worthwhile activity -- except for carrots, beets, and spinach. These three vegetables are more difficult to clean and sterilize than are others and they may pick up soil nitrates. The intestinal tracts of infants are unable to handle these soil nitrates properly. Procedures used in commercial canning of carrots, beets, and spinach for infants make these foods unquestionably safe.
Chunk-style or pureed fruit with or without sugar can be canned. Pack in half-pint, preferably, or pint jars and process for 20 minutes in a boiling-water canner.
Do not attempt to can pureed vegetables, red meats, or poultry meats, because proper processing times for pureed foods have not been determined for home use. Instead, can and store these foods using the standard processing procedures; puree or blend them at serving time. Heat the blended foods to boiling, simmer for 10 minutes, cool, and serve. Store unused portions in the refrigerator and use within 2 days.
Q. Why do tomatoes need to be acidified before canning?
A. Tomatoes usually are considered an acid food, but the results of some growing conditions have put pH values only slightly above the safe pH level. If they are to be canned as an acid food they must be acidified. To acidify, add 2 tablespoons of bottled lemon juice or 1/2 teaspoon of citric acid per quart of tomatoes. For pints, use 1 tablespoon bottled lemon juice or 1/4 teaspoon citric acid. Acid should be added directly to the jars before filling with product. Add sugar to offset acid taste, if desired. Four tablespoons of a 5-percent acidity vinegar per quart may be used instead of lemon juice or citric acid. However, vinegar may cause undesirable flavor changes. Do not use fresh lemon juice since its acidity varies.
Q. What are important factors in preparing tomatoes for home canning?
A. Use ripe, juicy tomatoes. Never use overripe tomatoes, because tomatoes lose acidity as they mature. Tomatoes with soft or decayed areas are not suitable for canning. Be careful to remove all of the stem and green parts. Acidify each jar according to the procedure above.
Q. Does ascorbic acid help keep fruits and vegetables from darkening?
A. Yes. Adding 1/4 teaspoon of crystalline ascorbic acid (vitamin C) to a quart of fruit or vegetable before it is processed retards oxidation, which is one cause of canned foods darkening. Ascorbic acid preparations containing sugar can be used with fruits in proportions suggested by manufacturer.
Q. There is mold on the surface of my home-canned tomatoes, applesauce, and jelly. Is it all right to remove the mold and use the food?
A. Discard any home-canned food with mold on or in the food. It could be dangerous. It is possible for mold growing on the surface to lower the acidity of the food. If the food becomes low enough in acid, botulism-producing bacteria can start to grow and produce toxin. Even if the mold is scraped off the surface, the toxin remains in the food. Molds, too, produce toxin so that the food should be discarded.
Q. Can fruit be canned with artificial sweeteners?
A. Canning with artificial sweeteners or sugar substitutes is not recommended. Artificial sweeteners may lose some of their sweetening power when heated and may become bitter. Can fruit in water or unsweetened juice and add the sugar substitute when serving.
Q. Why does fruit float in jam?
A. Fruit was not fully ripe, was not thoroughly crushed or ground, was not cooked long enough or was not properly packed in jars. To help prevent floating fruit, remove pan from heat as soon as jam is cooked; then alternately stir and skim the jam for 5 minutes.
Q. Is it necessary to process jams and preserves in a boiling-water-bath canner?
A. Yes. This prevents growth of molds and yeasts that could cause food spoilage and quality changes.
Q. Why do crystals form in jelly?
A. Crystals throughout the jelly may be caused by too much sugar in the jelly mixture or by cooking the mixture too little, too slowly, or too long. Evaporation of liquid causes crystals that form at the top of jelly that has been opened and allowed to stand. Crystals in grape jelly may be tartrate crystals. (To prevent tartrate crystals in grape jelly, let juice stand in a cool place overnight, then strain through two thickness' of damp cheesecloth to remove crystals.)
Q. What causes jelly to be too soft?
A. One or more of these may be the cause: Too much juice in the mixture. Too little sugar. Mixture not acid enough. Making too big a batch at one time.
Q. What can be done to make soft jellies firmer?
A. Soft jellies can sometimes be improved by recooking according to the directions. It is best to recook only 4 to 6 cups of jelly at one time.
To remake with powdered pectin. Measure the jelly to be recooked. For each quart of jelly, measure 1/4 cup sugar, 1/4 cup water, and 4 teaspoons powdered pectin. Mix the pectin and water and bring to boil, stirring constantly to prevent scorching. Add the jelly and sugar. Stir thoroughly. Bring to a full, rolling boil over high heat, stirring constantly. Boil mixture hard for 1/2 minute. Remove jelly from the heat, skim, pour into hot containers, seal, and process.
To remake with liquid pectin. Measure the jelly to be recooked. For each quart of jelly, measure 3/4 cup sugar, 2 tablespoons lemon juice, and 2 tablespoons liquid pectin. Bring jelly to boiling over high heat. Quickly add the sugar, lemon juice, and pectin and bring to a full rolling boil; stir constantly. Boil mixture hard for 1 minute. Remove jelly from the heat, skim, pour into hot container, seal, and process.
To remake without added pectin. Heat the jelly to boiling and boil for a few minutes. Test to determine just how long to cook it. Remove jelly from the heat, skim, pour into hot container, seal, and process.
Q. What makes jelly syrupy?
A. Too little pectin, acid, or sugar. Excess sugar can also cause syrupy jelly.
Q. What causes weeping jelly?
A. Too much acid. Storage place was too warm or storage temperature fluctuated.
Q. What makes jelly too stiff?
A. Too much pectin (fruit was not ripe enough or too much pectin added); overcooking.
Q. What causes fermentation of jelly?
A. Too little sugar or improper sealing.
Q. Why does mold form on jelly or jam?
A. Because an imperfect seal has made it possible for mold and air to get into the container.
Q. What causes jelly or jam to darken at the top of the container?
A. Stored in too warm a place, or a faulty seal allows air to leak in.
Q. What causes jelly and jam to fade?
A. Too warm a storage place or too long storage. Red fruits (such as strawberries and raspberries) are especially likely to fade.
Q. What makes jelly cloudy?
A. One or more of these may cause cloudy jelly: Pouring jelly mixture into jars too slowly. Allowing jelly mixture to stand before it is poured. Juice was not properly strained and contained pulp. Jelly set too fast, usually the result of using too-green fruit.
Q. What makes jelly gummy?
A. Overcooking.
Q. Can commercial canned or frozen fruit juice be used for making jelly?
A. It is best to use commercially canned or frozen fruit juice only in recipes with added pectin. Because fully ripe fruit is used, the amount of pectin in commercial juice may be too low to get a satisfactory gel without added pectin.
Q. If you are making jelly or jam with liquid pectin, when do you add it?
A. Liquid pectin is added to the cooked juice or fruit and sugar mixture immediately after it is removed from the heat.
Q. If you are making jelly or jam with powdered pectin, when do you add it?
A. Powdered pectin is added to the unheated fruit juice or crushed fruit.
Q. How do I prepare paraffin for sealing jelly?
A. Paraffin is no longer recommended for sealing jellies or any other sweet spread because of the potential for mold growth. All sweet spreads should be sealed with two-piece, self-sealing lids and processed for 5 minutes in a boiling-water canner.
Q. Can a recipe for jam or jelly be doubled?
A. Never double a jelly or jam recipe. If a double batch of jelly or jam is cooked for the usual time, it will be undercooked -- which means the jelly or jam will be soft and runny. If boiled longer, it will have a caramelized flavor and dark color.
Q. What kind of container should be used for making pickles?
A. Use utensils of unchipped enamelware, stainless steel, aluminum, or glass for heating pickling liquids. Do not use copper, brass, galvanized, or iron utensils. These metals may react with acids or salts and cause undesirable color changes in pickles or form undesirable compounds. Do not store pickling liquid in stainless steel or aluminum utensils. Pitting will occur.
Use a crock or stone jar, unchipped enamel-lined pan, or large glass jar, bowl, or casserole for fermenting or brining. Stainless steel containers are not recommended for brining pickles because pitting of the container will occur over time because salt in the brine is corrosive.
Q. Can alterations in a pickle or relish recipe be made safely?
A. The level of acidity in a pickled product is as important to its safety as it is to taste and texture. Do not alter vinegar, food, or water proportions in a recipe or use a vinegar with unknown acidity. Use only recipes with tested proportions of ingredients. There must be a minimum, uniform level of acid throughout the mixed product to prevent the growth of botulinum bacteria.
Q. What causes pickles to taste bitter?
A. There are several possible causes for bitter-tasting pickles, including:
Q. What causes pickles to be hollow?
A. Hollowness in pickles usually results from poorly developed cucumbers, keeping cucumbers too long before pickling, too rapid fermentation, or too strong or too weak a brine during fermentation.
Q. What causes soft or slippery pickles?
A. These generally result from microbial action, which causes spoilage. Once a pickle becomes soft, it cannot be made firm. Microbial activity may be caused by too little salt or acid, cucumbers not covered with brine during fermentation, and scum scattered throughout the brine during fermentation. Other causes are insufficient heat treatment, a seal that is not airtight, and moldy garlic or spices. Blossoms, if not entirely removed from the cucumbers before fermentation, may contain fungi or yeasts responsible for enzymatic softening of pickles.
Q. Why do some pickles turn dark?
A. Use of ground spices, too much spice, iodized salt, overcooking, use of iron utensils, and minerals in water, especially iron, may cause darkness in pickles.
Q. What causes shriveled pickles?
A. Shriveling may result from using too strong a vinegar, sugar, or salt solution at the start of the pickling process. In making very sweet or very sour pickles, it is best to start with a diluted solution and increase it gradually to the desired strength. Overcooking or overprocessing also causes shriveling.
Q. Why should pickles be processed in a boiling-water-bath canner?
A. Pickle products require heat treatment to destroy organisms that cause spoilage and to inactivate enzymes that may affect flavor, color, and texture. There is always danger of spoilage organisms entering the food when it is transferred from kettle to jar. Adequate heating is best achieved by processing in a boiling-water-bath canner.
Q. Why does sauerkraut turn dark?
A. Darkness in sauerkraut may be caused by unwashed and improperly trimmed cabbage, insufficient juice to cover fermenting cabbage, uneven distribution of salt, exposure to air, high temperatures during fermentation, processing and storage, and long storage period.
Q. What contributes to an undesirable softness in kraut?
A. Softness in kraut may result from insufficient salt, temperatures too high during fermentation, uneven distribution of salt, and air pockets caused by improper packing.